Nail Stamp

13 Dec

One of the main reasons i went to Sally’s was to try and find a nail stamp. I never found it, they have a bunch online for cheap, but I don’t usually buy things online so I just left it. One day in Wal-mart I see a nail stamp package at the check-out, with the impulse buys. I had to buy it, it was only $14. The kit comes with a nail stamp stick, design plates, and scraper.

IMG_3536

I’ve heard this thing is quite finicky and takes just as long to use as doing the designs freehand.

I don’t use it very often because the prints that it comes with aren’t so great and it is a bit tedious, but it is nice to have because it produces the same image every time (the quality is debatable, you just have to take a look at the stamp, make sure the whole image made it on the stamp, before transferring it to your nail).

I found that for this technique, it works best with an older polish, more goopy and thick so that the design is solid and more noticeable. This is great cause then my old polishes don’t go to waste.

IMG_3172

This is what you get when you use a newer, thinner polish, the design isn’t as bold. The white is stamped on to the blue here.

IMG_3171

Steps for using the stamp:

  1. Place polish on image stencil plate
  2. Using the scraper, run it across the design with one fast smooth motion (apply pressure), to get rid of the access polish. If you didn’t take off all the access polish, scrape the section again.
  3. Stamp the image from the design plate to the stamp stick. Be sure pick up the entire image, apply some pressure and rock the stick from one side to the other
  4. Check to see that the design on the stamp stick looks like how you want it to on your nail. If a portion of it did not transfer or it smeared, redo it (steps 7 and 8, then steps 1-3).
  5. Align the design with your nail in the orientation that you want it
  6. Using the rocking motion again, press the stamp onto your nail

        Ta Da!! One nail is done!

Clean up, must be done each time, between every nail:

  1. Using a Q-tip, get it wet with nail polish remover and clean up the stamp stick and stencil design plate
  2. The scraper will have an access of polish stuck to it, it is helpfully to wipe it on a napkin before rubbing it with the Q-tip
  3. Now, repeat steps 1-6 (stamping) and then steps 1-3 (cleaning) for each nail

Work quickly to get the best results. You don’t want the polish to dry on the design plate or stuck to the stamp stick because then you won’t get the complete picture onto your nail.

IMG_3211

IMG_3212

I am not a big fan of the design plates that came in my nail package. The images are mostly just flowers and kiddie picture, which are kind of big in size, one image would take up your whole nail. I would rather have varying sizes so that I can double/triple up on some designs. The individual images are bigger than preferred, but I find that the “wallpaper” design, used for the whole nail, is too small. I had to use the design twice to cover the whole nail, which is very difficult because it’s like lining up wall paper, but smaller scale and from a secondary source (the stamper).

IMG_3177

Here you can see where the edges are where the design doesn’t line up because I was just winging it and didn’t bother trying to line up the stars in particular. I think even if I were to try, it would not work very well anyways.

IMG_3176

 

 

IMG_3197

IMG_3202

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: